A little clarity for your water

Water Softener CalculatorBetter water.
Better settings.

Take the guesswork out of your water softener. Find the right regeneration schedule, salt dosage, and settings for your home.

Free to useNo sign-upMade for your household
Settings for the systems you know
Fleck Clack GE Whirlpool Aquasure EcoPure
Personalized for your home

Water Softener Calculator

A few details in. A clear plan for your softener out.

01 / Your setup

Match the model and controller on your softener’s label. Mechanical dials and digital SXT controllers use different settings.

Fleck 5600SXT (digital)

20 GPM valve rating

Single-tank softener valve with an SXT electronic controller. Choose this model for a digital display with regeneration and arrow buttons.

SXT digital controllerMetered regenerationSingle tank
View on Amazon

Affiliate link — we may earn a commission at no extra cost to you.

Identify your model & find its manual
Pentair Fleck 5600SXT valve with an LCD and three round buttons
Manufacturer photo · Fleck 5600SXT (digital)

Look for a digital LCD above three buttons: regeneration, up, and down. Confirm 5600SXT on the valve or system paperwork; an SXT display alone does not identify the valve body.

Match the rating label and controller, rather than choosing by appearance alone. Assemblers may fit the same valve to different tank sizes.

Capacity & salt settings

Capacity changes with salt dose. Use a matched pair from your system manual, or a clearly labeled resin estimate.

The 5600SXT is a control valve. Enter the resin volume and operating capacity for the complete system installed in your home.

These approximate standard-resin operating points are not certified settings for your model. Resin estimate reference

Planning assumption, not a factory default. Demand-controlled systems may calculate reserve automatically.

5600SXT programming details

Read the BLFC label and meter model on your installation. Leave unknown values blank; the result will tell you what to confirm.

Don't know your water hardness?

Test your water at home with one of these kits for the most accurate softener settings.

Affiliate link — we may earn a commission at no extra cost to you.

Best value$11-14

JNW Direct Water Hardness Test Strips

150 strips

Quick and accurate hardness testing with easy-to-read color chart. Great for regular monitoring.

View on Amazon
Most comprehensive$20-25

Varify 17-in-1 Water Test Kit

17 parameters

Tests hardness, iron, pH, chlorine, lead, and 12 more parameters. Full water quality picture.

View on Amazon
Professional grade$25-30

SJ Wave 22-in-1 Water Test Kit

22 parameters

Professional-level accuracy with detailed testing for hardness, metals, and contaminants.

View on Amazon
A little know-how goes a long way

Good water starts with good answers.

Practical guides for a softer-running home.

How this calculator works

Most water softeners leave the factory on generic default settings that rarely match the water in your home. Set the hardness too low and the resin exhausts before it regenerates, so hard water slips through; set it too high, or regenerate too often, and you waste salt and water every cycle. This calculator turns three numbers you can measure or estimate — your water hardness, your dissolved iron level, and your daily water use — into settings tuned to your situation instead.

The calculator converts measured hardness to grains per gallon and adds five GPG per PPM of dissolved clear-water iron. Daily demand is compensated hardness multiplied by your water use. A matched capacity and salt-dose pair comes from the selected manufacturer operating point, your documented settings, or a labeled generic resin estimate. We subtract your chosen reserve and divide the remaining capacity by daily demand. Short intervals stay short; the calculator does not stretch an undersized system to a three-day minimum. Refill time is only estimated when you supply the installed BLFC flow rate. Other cycle times remain installation-specific.

Treat the results as a well-reasoned starting point, not gospel. They assume a typical single-tank, downflow residential softener with standard resin, and they're only as good as the numbers you feed in — use a water test or measurements from your actual supplier, rather than a location-based guess. Unusual plumbing, very high iron, twin-tank or commercial systems, and manufacturer-specific quirks can all shift the ideal settings. If your water still isn't right after programming, the troubleshooting guide walks through the usual causes, and when in doubt a licensed water-treatment professional can dial in your specific setup.

Disclaimer

This calculator is provided "as is" without warranties. Results are for reference only and should be verified by a qualified professional. Local water conditions and regulations may affect actual requirements. Always consult a licensed plumber or water treatment professional before making changes to your system.