How to Program a Fleck 5600SXT
This guide covers a Fleck 5600SXT in a single-tank, downflow, metered softener installation. It explains how to reach the settings and distinguish calculated water-use values from hardware settings that must match your system. A valve model alone does not determine the tank’s capacity, salt dose, injector, refill flow control, or flow meter.
Set the time of day first
Hold either arrow until the display enters clock setting and shows TD, adjust with Up/Down, then press Extra Cycle to return to service. A meter-delayed installation schedules regeneration at its programmed time after its usable gallon allowance reaches the reserve. The reserve is intended to cover the wait; it should not already be exhausted. Check AM/PM and restore the actual time after using the temporary Master Programming entry time below.
Entering Master Programming
Master Programming is where the real settings live. To open it:
- Confirm the system is in service and record the existing settings. Use the manual for your exact timer revision; the following sequence is from Pentair’s downflow manual linked below.
- Set the clock temporarily to 12:01 PM, then press Extra Cycle to leave clock setting. Hold Up and Down together until Display Format appears. With a normal clock time, the arrow combination opens User Programming instead.
- Use the Extra Cycle button — the circular-arrow / regen key — to advance from one parameter to the next.
- Use the Up/Down arrows to change whichever value is flashing on screen.
- When you have set the last parameter, press Extra Cycle once more to step past it. That saves your changes and returns the valve to the normal time display.
Some parameters depend on the selected control configuration and may not appear. If the screens do not match this sequence, stop and check the matching manual instead of changing unrelated options. Restore the real time of day after saving.
Write down the current values first
Before you change a single setting, step through the menu once and note every existing value on paper. If a new setting turns out wrong, you can roll straight back instead of guessing. Procedures and the exact parameter list vary slightly between firmware revisions and sub-models, so keep the configuration sheet that shipped with your valve alongside these notes.
Working through each parameter
Start with the documented operating capacity at the selected salt dose, not a blanket 32,000 grains for each cubic foot. Enter C using the units and display format your timer expects. Set H from the water test and applicable compensation, and choose a reserve allowance that can cover use before the next scheduled regeneration. The calculator starts with a one-day reserve planning assumption; it is editable and is not a manufacturer mandate. Pentair limits a fixed RC allowance to half the timer’s calculated gallon capacity.
Retain the installer’s VT, CT, NT, BW, BD, RR, and DO unless your system documentation calls for a change. DO is a separate maximum time between regenerations, not the capacity-derived interval. Pentair’s documented timer range is off to 99 days; neither a three-day minimum nor a fourteen-day cap is a universal setting. If capacity will run out sooner than the planned interval, review the system rather than extending the estimate to hide that shortfall.
BF depends on the salt dose and the installed brine-line flow control (BLFC). For a sodium-chloride planning estimate, refill minutes = salt pounds ÷ (3 × BLFC gallons per minute), assuming about three pounds dissolve per gallon of refill water. Check the label, salt type, timer increments, and supplier’s instructions before entering it. FM must match the actual meter: t0.7 and P0.7 describe different ¾-inch meter mechanisms. Leave either item unconfirmed in the calculator if you cannot identify it.
Parameter reference at a glance
Use the calculator to keep the capacity–salt-dose pair, selected reserve, confirmed BLFC, and meter information together. It generates a limited calculated reference; this table also explains hardware settings that remain installation-specific.
| Code | Setting | Value / action | What it does |
|---|---|---|---|
| DF | Display Format | Confirm units | Use the units configured for your system; Gal is the gallons option. |
| VT | Valve Type | Keep installer setting | The valve body and regeneration direction determine this setting. |
| CT | Control Type | Keep installer setting | Fd is meter-delayed operation; do not change the control mode just to match an example. |
| NT | Number of Tanks | Confirm installation | The calculator reference is only for a single-tank metered downflow installation. |
| C | Unit Capacity | Matched operating capacity | Use capacity at the selected salt dose, expressed in the units your display expects. A marketing grain rating is not a universal operating setting. |
| H | Hardness | Tested / compensated GPG | Use measured hardness with the compensation required for the water and system. |
| RS | Reserve Selection | Confirm reserve method | rc uses a fixed gallon reserve; SF uses a percentage. Do not apply both methods to the same allowance. |
| RC | Reserve Capacity | Selected reserve gallons | Allow for water needed before scheduled regeneration. The 5600SXT limits fixed reserve to half its calculated gallon capacity. |
| DO | Days Override | Keep installer setting | A separate maximum time between regenerations, not the predicted capacity interval or a universal 3–14-day rule. |
| RT | Regeneration Time | Low-use hour | Choose an appropriate time for the household and confirm the clock. |
| BW | Backwash | Keep installer setting | Depends on the resin bed, flow control, and installation. |
| BD | Brine Draw + Slow Rinse | Keep installer setting | Depends on the injector, brine draw, and system instructions. |
| RR | Rapid Rinse | Keep installer setting | Retain the system-specific rinse duration. |
| BF | Brine Fill | Confirm BLFC | Estimate from salt dose and the installed brine-line flow control; do not use a fixed minutes-per-cubic-foot rule. |
| FM | Flow Meter | Confirm installed meter | t0.7 means a ¾-inch turbine; P0.7 means a ¾-inch paddle wheel. Choose the actual meter, not a guessed default. |
Test with one manual regeneration
Programming alone does not prove the plumbing works. Once you have saved your settings, trigger a single manual regeneration using the matching service manual. Observe brine draw and refill, check for leaks, and test outlet hardness afterward. Seeing water draw down and refill does not by itself prove the salt dose, capacity, or treated-water quality is correct. If draw or refill fails, follow the troubleshooting procedure before applying further programming changes.
Manufacturer references
The Pentair 5600SXT downflow manual documents programming entry, reserve limits, day override, and meter options. The Watts PWSCAB manual provides the approximate sodium-chloride dissolution and capacity–dose examples used for generic estimates; those examples are not certified ratings for every 5600SXT system.
Related guides
- Softener calculator — turn your tested hardness, daily water use, and a matched capacity–salt-dose pair into a planning reference.
- General programming guide — how to reach the settings menu on other models, including Clack WS1, GE, Whirlpool, and mechanical Fleck valves.
- Maintenance schedule and troubleshooting guide — keeping the softener running, and what to check if something is wrong after programming.